First, tighten the ring nut to approximately 18 Nm 1. Retighten the ring nut to specification. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. YZF-R1 M You can only view or download manuals with. Sign Up and get 5 for free. Table Of Contents. Quick Links. See also: Owner's Manual. Table of Contents.
Previous Page. Next Page. For complete service information procedures it is necessary to use this Supplementary Service Manual together with the following manual. Therefore, anyone who uses this book to perform maintenance and repairs on Yamaha vehicles should have a basic understanding of mechanics and the techniques to repair these types of vehicles.
Comprehensive explanations of all installation, removal, disassembly, assembly, repair and check procedures are laid out with the individual steps in sequential order. INFO Symbols 1 to 9 indicate the subject of each chapter.
Starter cable B Route the meter assembly lead through the left side of the headlight Main switch lead housing. H Fasten the wire harness to the headlight housing O Route the right handlebar switch lead behind the boss with a plastic locking tie.
Rear brake switch lead D Route the coolant reservoir breather hose over the Timing chain tensioner. J Route the sidestand switch lead and oil level switch D Route the seat lock cable over the wire harness.
E Fasten the wire harness with a plastic clamp. K Do not crush the water pump breather hose and F Make sure the rear flasher light lead coupler and plastic clip. R To the fuel tank. No hose must be inserted into the under cowling. S Insert the fuel tank breather hose into a back side O Pass the air filter drain hose and the coolant reser- nipple of fuel tank.
B Route the neutral switch lead direct to upper right side. G To the carburetor. B Route the horn lead over the horn bracket and H Route the coolant reservoir tank breather hose up- make sure that the lead has no slack.
Y Position the ground coupler over the main harness. In- should be not exceed just behind 30 mm of all coupler. If followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a longer service life and reduce the need for costly overhaul work.
This information applies to vehicles already in service as well as to new vehicles that are being prepared for sale. Page 42 S Adjust headlight beam if necessary. NOTE: D The annual checks must be performed once a year unless a 10, km or 20, km maintenance was performed in the same year.
To set the clock 1. TRIP B! TRIP A! Stopwatch mode Standard measurement 1. Split-time measurement 1. Coolant temperature display The coolant temperature display indicates the temperature of the coolant. Air intake temperature display The air intake temperature display indicates the temperature of the air drawn into the air filter case.
NOTE: S Even if the air intake temperature is set to be displayed, the coolant temperature warning light comes on when the engine overheats. Display brightness and shift timing indicator light control mode This mode cycles through five control functions, allowing you to make the following settings in the order listed below.
S Display brightness: This function allows you to adjust the brightness of the displays and tachometer to suit the outside lighting conditions. S Shift timing indicator light activity: This function allows you to choose whether or not the indicator light should be activated and whether it should flash or stay on when activated. S Shift timing indicator light activation: This function allows you to select the engine speed at which the indicator light will be activated. S Shift timing indicator light deactivation: This function allows you to select the engine speed at which the indicator light will be deactivated.
S Shift timing indicator light brightness: This function allows you to adjust the brightness of the indicator light to suit your preference. To adjust the brightness of the multifunction meter displays and tachometer 1. To set the shift timing indicator light activity function 1.
To adjust the shift timing indicator light brightness 1. During reassembly, properly oil all mating grease parts and bearings and lubricate the oil seal lips with grease. Tool No. Radiator cap tester Radiator cap tester Radiator cap tester adapter YU Adapter These tools are used to check the cooling system.
YU Steering nut wrench YU This tool is used to loosen or tighten the steering stem ring nuts. Damper rod holder This tool is used to hold the damper rod as- YM sembly when loosening or tightening the damper rod assembly bolt.
Oil filter wrench YU This tool is needed to loosen or tighten the oil filter cartridge. Rod holder YM This tool is used to support the damper ad- justing rod. Rod puller Rod puller Rod puller attachment YM Rod puller attachment These tools are used to pull up the front fork damper rod. YM Vacuum gauge YU This guide is used to synchronize the car- buretors. Compression Compression gauge gauge Compression gauge adapter YU These tools are used to measure engine Adapter compression.
YM Middle driven shaft Middle driven shaft bearing driver bearing driver Mechanical seal installer YM Mechanical seal These tools are used to install the water installer pump seal.
YM Clutch holding tool This tool is used to hold the clutch boss YM when removing or installing the clutch boss nut. Valve guide remover YM This tool is used to remove or install the valve guides.
Valve guide installer YM This tool is used to install the valve guides. Ignition checker YM This tool is used to check the ignition sys- tem components. Yamaha bond No. Digital circuit tester This tool is used to check the electrical sys- tem. Pivot shaft wrench Pivot shaft wrench Pivot shaft wrench adapter YM Pivot shaft wrench This tool is need to loosen or tighten the adapter spacer bolt.
Pocket tester YU This instrument is needed for checking the engine oil temperature. Oil pressure Oil pressure gauge gauge Adapter YU These tools are used to measure engine oil Adapter pressure. Engine tachometer This tool is needed for observing engine rpm. Fuel pressure adapter YM This tool is needed to measure fuel pres- sure. Pressure gauge YU This tool is used to measure fuel pressure.
Camshaft wrench YM This tool is used to hold and rotate the cam- shaft sprocket. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual.
Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file.
Get 1 for every download of your manual. Buy as much as you need. S a speedometer which shows the riding. S a tachometer witch shows engine speed. This tool is used to hold the damper rod as-.
This tool is needed to loosen or tighten the.
0コメント